|
Type R1S10
Plastic paddle flow switch, high rating, 3/4"F mobile nut
JPC patented mechanism, magnet type
Fluid: water or liquids compatible with PC plastic resin, without magnetic particules
Pipe nominal dimension : 3/4" to 4" Housing : PC Wetted surfaces : PC, nickel
Paddle length : product includes a set of 5 different snap-on paddle discs to cover pipe size from 3/4" to 4".
Paddle disc position can be adjusted by customer to set tripping point.
Pipe fittings :G 3/4"female / NPT 3/4" female
Line maximum operational pressure : 5 bars (0.5 Mpa, 70PSI)
Water temperature : 10 to 90°C Ambient t° : max 55°C
Water protection : IP55 (electrical connector not included)
Electrical rating : 20A, 2HP 250V (20.000 cycles)
Contact : SPST double break (JPC patented mechanism)
Terminals : 6.3 x 0.8mm QC terminals. Cable on request
Set point adjustment : Switch mechanism is factory sealed. Paddle disc choice and position are customer adjustable
|
|
|
Type R35B20
Inline flow switch, 1/2" male x 1/2" male
Equipment protection, for low flow applications
Fluid: water, clean and filtered
Pipe nominal dimension : DN 15mm Housing : PA66 30% FG
Wetted surfaces : PA66 30% FG, Nickel
Pipe fittings : 1/2" BSP male (G1/2B, NFE 03-005)
Water pressure drop :lower than 0.7bar (10 PSI) at 15 liters/min (4GPM)
Line maximum operational pressure : 10 bars (1 Mpa, 140PSI)
Line minimum pressure : 0.1 bar (1.5 PSI)
Water temperature : 10 to 80°C
Water protection : IP54 (electrical connector not included)
Electrical connection :
- Molex connector type 3-06-1023 with 100mm long wires 0.5mm²
- Built in AMP mate and lock (to be connected to AMP 172336-1 housing, and AMP 170362-1 terminals)
- Wires without connector, length on request
|
Electrical rating : 12VA, max 0.5A, max 220V (rating up to 60VA on request)
Contact : SPST, close on flow rise contact (open on flow rise on request) 2 contacts on request
Contact resistance : lower than 200 mOhms, 300mOhms with 100mm wires and connector
Set point adjustment : factory setting only
Set point limits : flow rate to activate contact 115 to 200L/h (1.9 to 3.4l/min)
Differential : 0.5 +/-0.3 l/min
Accessories : pipe union and spigots for solvent gluing, surface mounting bracket
|
|
 |
Type R35B21
Inline flow switch, snap on pipe connections
Customised version with snap on fluid connections or other threads on request.
Same technical data as R35B20
|
|
|
Type R36B23
Inline flow switch, 3/4" male x3/4" male
Typical uses :
equipment protection for low flow applications in pumps, gas water heaters, gas boilers, heating elements,
solar systems, pool cleaners,ozone generators, ultraviolet systems
Fluid: water, clean and filtered
Pipe nominal dimension : DN 20mm Housing : PPO (WRC or FDA approved)
Wetted surfaces : PPO, Nickel
Pipe fittings : 3/4" BSP male (G3/4B, NFE 03-005)
Water pressure drop :lower than 0.2bar (2.8 PSI) at 10 liters/min (2.6GPM)
Line maximum operational pressure : 15 bars (1.5 Mpa, 220PSI)
Line minimum pressure : 0.1 bar (1.5 PSI)
|
Water temperature : 5 to 80°C permanent
Ambient temperature : 60°C max
Installation position : vertical, +/-5°, water outlet upside
Water protection : IP54 (electrical connector not included)
Maximum particules size : 1mm maximum. No magnetic particule allowed
Electrical connection :
- standard : Built in AMP mate and lock (to be connected to AMP 172336-1 housing, and AMP 170362-1 terminals)
- on request : 100mm long wires with molex connector type 3-06-1023
- other wire lengths and connectors
Electrical rating : 12VA, max 0.5A, max 220V (rating up to 60VA on request)
Contact : SPST, close on flow rise contact (open on flow rise on request)
Contact resistance : lower than 200 mOhms, 300mOhms with 100mm wires and connector
Set point adjustment : factory setting only
Set point limits : flow rate to activate contact 100 to 270L/h (1.7 to 4.5l/min)
Differential : 0.5 +/-0.3 l/min
Accessories : pipe union and spigots for solvent gluing
|
|
 |
Type R3BB22
Inline flow switch, brass, G1/2" male x G1/2" female.
Same technical data as R36B23
|
|
|
Type R38B2
Inline flow switch, barbed connection for 3/8" ID soft PVC tubing
Very low flow 3 to 6 GPH (0.2-0.4L/min)<
Typical uses :
equipment protection for very low flow applications in peristaltic pumps, pool and
spas water sterilization systems, ozone generators, ultraviolet systems
Fluid: water, clean and filtered
Pipe nominal dimension : DN 8 (1/4") Housing : PA66 30% FG
Wetted surfaces : PA66 30% FG, nickel
Pipe fittings : 2 barbed connections for 3/8" internal diameter soft tubing or
1 barbed connection for 3/8" ID soft tubing and 1 slip dia 14mm for metric or 1/4" PVC pipe
Water pressure drop :lower than 0.7 bar (10 PSI) at 1.5 liter/min (0.4 GPM)
Line maximum operational pressure : 10 bars (1 Mpa, 140 PSI)
Line minimum pressure : 0.1 Bar(1.5 PSI)
Water temperature : 10 to 80°C permanent
Installation position : vertical, +/-5°, water outlet upside
Water protection : IP54 (electrical connector not included)
Maximum particules size : 1mm maximum. No magnetic particule allowed
|
Electrical connection :
- Molex connector type 3-06-1023 with 100mm long wires 0.5mm²
- Built-in AMP mate and lock (to be connected to AMP 172336-1 housing, and AMP 170362-1 terminals)
- Wires without connector, length on request
Electrical rating : 12VA, max 0.5A, max 220V (rating up to 60VA on request)
Contact : SPST, close on flow rise contact (open on flow rise on request)
Contact resistance : lower than 200 mOhms, 300 mOhms with 100mm wires and connector
Set point adjustment : factory setting only
Set point limits : flow rate to activate contact 115 to 200L/h (0.2 to 0.4L/min)
Differential : 0.05 +/-0.02 L/min
Accessories : pipe union and spigots for solvent gluing
|
|
|
Type R1A0
Miniature flow switch, stainless steel paddle, 3/4" mobile nut
Fluid: water
Pipe nominal dimension : 3/4" to 4"
Housing : PC
Wetted surfaces : PC, stainless steel, TPE
Pipe fittings : G 3/4" female or NPT 3/4" female
Line maximum operational pressure : 5 bars (0.5 Mpa, 70 PSI)
|
Water temperature : 10 to 80°C
Ambient temperature : max 55°C
Installation position : any
Water protection : IP55 (electrical connector not included)
Maximum particules size : 1mm maximum. No magnetic particule allowed
Electrical connection : 1 meter long 3x0.5mm². 6.3 x 0.8 tab independent earth connection
Electrical rating : 3(1)A 250VAC
Contact : SPDT
Contact resistance : lower than 50 mOhms (without wires)
Set point adjustment : factory setting only
Set point limits : flow rate to activate contact depends on pipe diameter and paddle size
Differential : 0.05 +/-0.02 L/min
Accessories : pipe union and spigots for solvent gluing
|
|
|
Type R1F20
Plastic paddle flow switch, 12VA, reed switch type, 1/2" NPT male thread
Fluid: water, without magnetic particules
Pipe nominal dimension : 3/4" to 4" Housing : PA66
Wetted surfaces : PA66
Standard paddle length : 50mm. Installation must let paddle have free movement
Pipe fittings : 1/2" NPT can be used for competitors replacement with 3/4"
or 1" fittings by mounting 1/2" x 3/4" or 1/2" x 1 pipe adaptators
Line maximum operational pressure : 5 bars (0.5 Mpa, 70 PSI)
Line minimum pressure : 14 bars(1.4 Mpa 200 PSI)
Water temperature : 10 to 80°C
Installation position : horizontal
Water protection : IP55 (electrical connector not included)
Electrical connection : 1 meter long AWG24 cable.
Electrical rating : 12VA, max 0.5A, max 220V (rating up to 60VA on request)
Contact : SPST
Contact resistance : lower than 300 mOhms, with 1m cable
Set point adjustment : factory setting only
|
|
